995 reviews analysed
1. Signswise 200x200mm 12V 220W Silicone Rubber Heating Heater for 3D Printer Heated Beds
2. 3D Printer Silicone Heated Pad, Heating Plate 310x310mmx1.5mm, 120V 750W for Creality CR-10 /CR-10S 3D Printers Heater Bed with Screw Holes /3M Adhesive
- Wonderful silicone heater for Creality CR-10 /CR-10S 3D printer build plate heating.
- Rated at 5 watts per square inch with fast and even heating
- Equipped with NTC 100K thermistor (Beta 25/50 3950K-1%) as temperature control sensor which is supported directly by Marlin firmware.
- 3M adhesive backing offers excellent and easy mounting onto most surfaces.
- Versatile and may be used in many other applications.
3. 510x510mm Silicon Heated Bed for CR-10S5 3D Printer with Digital Temperature Controller Heating up to 100°C Within 10 Minutes
- Heat the build bed to 100°C within 10 minutes,maximum heating to 120°C
- With Digital temperature controller ,set heating temperature freely
- Independent power plug, not connect to motherboard, so protect motherboard from burning
- Stick to original heated bed directly, easy to use
- Position hole is the same as original heated bed
* With independent temperature controller .need plug with independent power * Size: 510-510mm suit for CR-10S5.
*Power consumption :Maximum power 1200W
*The maximum heating temperature 120C（Celsius Degree）
* The back with 3M adhesive glue, can directly stick to the heated bed. need disassemble the S5 bed before assemble it
* The heated bad Maximum temperature resistant is 200C, long term working temperature condition is under 180C
* This is 28 hole version, beyond 24 postion hole, extra 4 hole is for cooling
* To ensure safety , the plugs are 3 pins
* When use, please do some test to find a suitable temperature for you to use, for example, when heating pad working , if you want heat the bed to 100C, please set the silicon heater to 75-80C, no need to set to 100C, for the printer itself can heat too. this can save electricity cost and environment friendly
4. USA Material CR10 S4 Silicone Heater Pad 400x400mm for CR-10 S4 3D Printer Bed w/Screw Holes, Adhesive Backing + Sensor (120V)
- high temperature silicone heater pad for Creality CR-10 S4 3D printer
- This silicone heating pad with 4 pre-made screw holes as the drawing shows is designed for CR-10 S4 3D printer building plate.
- With 1.2meter NTC 100K 3950 thermistor for temperature Control (Choose Number 1 in the Marlin firmware)
- Please DO NOT POKE NEW HOLES for this bed as the whole pad is a circuit, so it will 100% damage the circuit if you poke new holes anywhere
- Important Notes: Please heat only after being mounted onto the plate. Do Not heating without proper heat-sink.
This silicone heating pad with 4 pre-made screw holes as the drawing shows is designed for CR-10 S4 3D printer building plate.
Backing:3M adhesive backing
It’s Electricity AND Heat you are coping with. We are absolutely your right choice with 100% guarantee for high quality heaters
Much safer and more reliable heat source than RepRap PCB heatbeds.
With 1.2meter NTC 100K 3950 thermistor for temperature Control.
Power consumption: 1000W.
Attached with two pieces 1.2meter length power wire
5. Creality Original Ultra Flexible Removable Magnetic 3D Printer Build Surface Heated Bed Cover for Ender 3/Ender 3 pro/Ender 5 3D Printer 235X235MM
- ALL NEW FUNCTIONALITY: Introducing the first ever removable, magnetically secured, build surface for hassle free model removal. Say goodbye to all those removal tools, spatulas, and knives with this genius design.
- EASY MODEL REMOVAL: The first 3D printing surface designed with model removal in mind. This surface is easily removed, and flexible. Simply print on the surface, remove the upper magnetic surface from the lower, bend the flexible surface and watch the model fall right into your hands.
- CUSTOMIZABLE: The flexible surface can easily be cut to any demensions making it perfect for all build sizes and all FDM printer models.
- SIMPLE INSTALLATION: Build surface comes with upper magnetic build surface and lower magnetic adhesive base. Place lower 3M adhesive surface on top of normal build plate.
- UNIVERSAL: Works with all FDM printer models, and all heated and non-heated 3D printer beds.
Easy removal 3D printing platform for PLA and PLA-based materials. To use it, simply stick the bottom plate onto your build plate and start printing, peel up the top plate with finished prints, then peel off the top plate from the prints.
6. CHPOWER Creality CR-10 Bed Surface, CR-10S Ultra-Flexible Removable Magnetic Build Surface 3D Printer Heated Bed Cover, 310x310mm
- EASY REMOVAL OF PRINTS: CR-10 upgrade parts, simply prints on the surface, remove the upper magnetic surface from the lower, bend the flexible surface and watch the model fall right into your hands. The first 3D printing surface designed with model removal in mind. This surface is easily removed, and flexible.
- SIZE: 300x300mm magnetic bed. Suitable for all FDM printer models, and all heated and non-heated 3D printer beds.
- DURABILITY & EASY CLEAN: CR-10 bed surface is capable to work at 70ºC. Easy clean with alcohol.
- SIMPLE INSTALLATION: This CR-10 plate comes with upper magnetic build surface and lower magnetic adhesive base. Place lower 3M adhesive surface on top of normal build plate.
- MORE FLAT FOR PRECISION: Super Flatness. Prevent warping. Fast and uniform heating. More precise on printing, especially the bottom of the prints.
The product is divided into two parts: the form of A+B
– Part A: The top is a matte surface (the same as other stickers), and the back is magnetic (the interaction with the front of Part B plays an attractive role)
– Part B: The top is magnetic (with the adsorption under the A part), the back is the 3M adhesive (posted on the printer platform, which plays a fixed role)
Easy removal Magnetic CR-10/CR-10S 3D printing platform for PLA filament material. To use this cr-10 bed surface, simply stick the bottom plate onto your build plate and start printing, peel up the top plate with finished prints, then peel off the top plate from the prints. Snap the top plate back into place for next round of printing.
1. Introducing the first ever removable, magnetically secured, cr-10 build plate for hassle free model removal. Say goodbye to all those removal tools, spatulas, and knives with this genius design.
2. Flexible 3D Printing CR10 Build Plate: reusable, provides a durable and stable build surface whilst preventing model warping.
1. This CR-10S Magnetic Build Surface is rated for PLA filaments ONLY. Any other filaments with high shrinkage coefficients may experience malfunction or decrease in magnetic force over time. This will not prevent your printing from warping.
2. This cr-10 build mat 300 x 300 is not for use with high-temperature printing applications above 70°C.
7. MK2B Heated Bed with Soldered NTC 3950 Thermistor – 3D Printer PCB Heatbed for MakerBot RepRap UP Mendel I3 Printer
- PCB HEATBED: Keep your print model warm and malleable during the entire printing process for a spectacular final result.
- PREVENT WARPING:Use the heat bed to improve adhesion – model stays flat on the print bed without corners lifting.
- COMPATABILITY: MK2B 214mm x 214 mm (8.4 in x 8.4 in) 12V or 24V Hot Bed for MakerBot RepRap UP Mendel I3 Printer.
- No Soldering Required: The PCB Heat Bed is supplied with integrated 100K ohm NTC 3950 Thermistor and soldered power leads.
- AMX3D ACCESSORIES: The best 3D Prints start with the best tools! AMX3d provides 3D printing supplies of the highest quality. If there are any problems with your Heat Bed just let us know!
3D Printer PCB Heatbed
Keeping your 3D print warm during the entire process can be the difference between a great final result and a disappointment. This PCB hot bed is designed to keep the material malleable and avoid the edges of your model cooling faster than the interior, which can lead to warping.
Improving adhesion and maintaining a flat base on the print bed, the MK2B hot bed includes a soldered 100K ohm NTC 3950 thermistor and soldered power cord, making this heated bed ready to use.
Featuring red soldermask and white silkscreen on both sides, the 12V or 24V 3D Printer Heated Bed is designed for the MakerBot RepRap UP Mendel I3 Printer, and measures 214mm x 214mm (8.4 in x 8.4 in).
- MK2B: 12V or 24V Heated Bed
- 214mm x 214 mm (8.4 in x 8.4 in)
- Thermistor included: 100K ohm NTC 3950, soldered and installed
- Soldered power leads
AMX3d 3D Printing Tools
Great 3D prints start with the best tools. Providing everything you need for truly spectacular results (just like the ones on the 3D printer box!), AMX3d only sell the highest quality 3D print accessories and toolkits, so you won’t be disappointed.
8. SIMAX 3D-Printer Heated-Bed Platform,Heating-Plate 24V/12V Changeable 235x235x3mm Aluminum Hot Bed for Ender3,CR10, Updated Version of MK2B & MK2A,Black
- ✔️【Stable Performance】The whole board full gold process, the cost is much higher than the spray tin plate,more slight, thin, stronger, excellent thermal conductivity and heat resistance
- ✔️【Quality Assurance】The new circuit, power supply power stability,safer to use, better print quality and more stable performance.
- ✔️ 【Easy Install】Easy to use and install, has a long service life,the vacancy is a counterbore and the mounting screws will not protrude.It is a prefect accessory for 3D printer.
- ✔️【No Need Glass】The whole board after optical short circuit, open circuit detection，3mm thick aluminum substrate is used, the heatbed and the aluminum plate are combined into one, no need to add glass.
- ✔️【100% QUALITY ASSURANCE】1-Year Warranty, if you are not satisfied with the product, please contact us in time, we will solve your problem within 24 hours and provide a 1-year warranty.
Thermistor length: 1m
Cable length: 1M / 3.3in
Support voltage: 240w 24V DC
DC24V: 130℃, 411W
Heating Area: 235 x 235mm
Item weight: 900g / 2.0lb
Package weight: About 1000g / 2.2lb
Heating bed cable description:
1. Project type: hotbed line for 3d printer
2. Applies to: All CR-10 3D printers.
CR-10 3D printer heater supports 24V power supply
Due to the different measurement methods, the size will be a bit error, the error is about 1mm, the actual measurement shall prevail.
24V wiring method: Weld Number 2 for positive, Number 3 for negative, 1 is empty
1 * Aluminum Heatbed
1* 1m Cable
9. 3D Parts Heater Bed of Ender 3 / Ender 3 Pro 3D Printer Replacement Parts Aluminum MK3 Heatbed Hotbed Platform with Heated Bed Cable Line for Ender-3 /Ender 3X /Ender 3 Pro 3D Printers DIY Kit
- DC 24V 220W Heater Bed Aluminum with Cable Installed and Build Surface Plate for Creality 3D Printer Ender 3
- Original Replacement Parts / Accessories for Ender 3 / Ender 3 PRo / Ender 3X 3D Printer
- Size of Hot Bed: 235x235x3mm
- Hotbed with Cable Which be Installed Well. Build Surface with 3M Adhesive which easily to stick on the heater bed platform.
- Warranty: All 3D printer accessories with Free Technical Support.
UCHOOSE, a King Professional 3D printer and Printing Parts Store.
For High Quality & Good Service, we are diligent to Do Our Best!
Note: These are original replacement parts for Creality 3D Printer Ender 3 / Ender 3 Pro / Ender 3X
Specifications of Heater Bed:
Model: dc24v 220w Aluminum hotbed for 3D Printer Ender 3
Product process: Aluminum Substrate
Hot Bed Size: 235x235x3mm
2) Specifications of Printing Build Surface:
Creality 3D Printers replacement Parts Printing Build Surface for Ender 3
Size: 235mm x 235mm
Background is made of 3M adhesive, easily stick on the heater bed platform.
Build sheet adheres to a print bed to help the filament stick during printing, while also enabling
clean removal of the printed part afterward
Compatible with ABS, PLA, HIPS and the other filament
Single sheet design installs more quickly and with fewer bubbles than tape or films
Durable construction allows for multiple uses with either the same or different filament material
HOW TO USE THE BUILD SURFACE:
There are 2 methods to attaching the build surface on heater bed:
1. clamp the build surface to the print bed using binder clips（at least 3 clips)
2. Torn off 3M tape on back and stick it on heater bed.
1 × Aluminum DC24V 220W Heater Bed 235x235x3mm With Cable Which be installed well
1X 3D Printing Printer Build Surface.
By our suggestions above, we hope that you can found Heating Bed 3D Printer for you.Please don’t forget to share your experience by comment in this post. Thank you!